Integrating a geothermal heat pump creates energy and emissions savings in a heating and cooling system equivalent to planting 750 trees or removing two cars from the highways. These heat pumps are engineered for use with forced-air systems in which conventional ductwork distributes hot or cold air. Reversible to generate heat in winter and cooling in summer.

Products:
Ultra® | 2000™ | Vara™ | Vara 2 Plus®

Quick tip: click the links above to quickly jump to a specific product below on this page.

ECONAR GeoSource Ultra®, Forced Air 3-, 4-, 5-, and 7-Ton Heat Pumps

Many times more efficient than heat pumps that extract heat from the air, and much safer and cleaner than a furnace

High-capacity exchangers provide up to 100% of heating so a back-up system is not necessary

Accessories include an electronic thermostat, polyethylene plastic earth-loop piping for maximum heat transfer, and a PumpPAK™ for simplified installation and quiet operation

Air Heat Exchanger - High-density technology air coil with copper tubing in aluminum fins designed for cold climates provide the highest heating output in the industry at comparable cooling capacities

Water Heat Exchanger – Brazed-plate stainless-steel heat exchangers provide maximum heat exchange at minimum pump pressure for reduced pumping costs

Electrical Controls - Compressor lockout is activated by electronic monitoring of low or high pressure for maximum system protection

Filter/Drier - Assures a clean, dry refrigeration circuit

Reversing Valve - All copper with low-pressure drop for maximum efficiency

Hot-Water Generator (Optional) - A double-wall desuperheater coil saves up to 65% on annual domestic water heating costs

Refrigerant - R410a refrigerant, a chlorine-free HFC refrigerant that does not harm the Earth’s ozone layer

Blower - Standard high-efficiency PSC motor or Optional Variable speed Electronically Commutated Motor (ECM) provides quiet, efficient air circulation

Thermostatic Expansion Valve - State-of-the art thermostatic expansion valve provides precise refrigeration control under a wide range of conditions

Charge Optimizer - Balances refrigerant charge in heating and cooling modes allowing optimum ColdClimate capacities and efficiencies

Compressor - A hermetically sealed, Compliant Scroll™ by Copeland® delivers the highest efficiency and lowest sound level in the industry

Cabinet - Vertical or horizontal configuration with fully insulated baked-on powder epoxy finish over galvaneal metal resists corrosion

 

back to top

ECONAR GeoSource 2000™ Forced Air, 1.5- to 10-Ton Heat Pumps

Saves up to 70% on annual heating and cooling costs

Technology saves on water-heating costs in winter and provides free hot water in summer

Air Heat Exchanger - High-density technology air coil with copper tubing in aluminum fins designed for cold climates provide the highest heating output in the industry at comparable cooling capacities

Electrical Controls - Compressor lockout activated by electronic freeze protection or high-pressure switch for maximum system protection. Compressor and fan motors are staged for a softer start

Reversing Valve - All copper with low-pressure drop for maximum efficiency

Blower – High-efficiency, direct-drive PSC multi-speed, slides in and out

Water Heat Exchanger – Brazed-plate stainless-steel heat exchangers provide maximum heat exchange and minimum pump pressure for reduced pumping costs

Hot Water Generator (Optional) - A double-wall desuperheater coil saves up to 65% of annual domestic water heating costs

Cabinet - Vertical or horizontal configuration with fully insulated baked-on powder epoxy finish over galvaneal metal resists corrosion

Filter/Dryer - Assures a clean, dry refrigeration circuit

Refrigerant - Utilizes R22 refrigerant

Refrigerant Expansion Valve - State-of-the-art thermostatic expansion valve provides precise refrigeration control

Receiver - Allows a balance of heating and cooling capacities without compromising dehumidification

Compressor - A hermetically sealed, pistonless Compliant Scroll™ by Copeland® delivers the highest efficiency and lowest sound level in the industry

Air Pad (Optional) - For quieter operation

 

back to top

ECONAR GeoSource Vara™ Forced Air 3- to 6-Ton Heat Pumps

Blower – Variable-speed Electronically Commutated Motor (ECM) provides quiet, efficient air circulation at a constant low-airflow rate to reduce hot and cold spots throughout the building, providing better comfort and reducing the need for the heat pump to cycle on and off

Air Heat Exchanger - High-density technology air coil with copper tubing in aluminum fins designed for cold climates providing the highest heating output in the industry at comparable cooling capacities

Electrical Controls - Compressor lockout is activated by electronic freeze protection or high-pressure switch for maximum system protection. Compressor and fan motors are staged for a softer start

Filter/Drier - Assures a clean, dry refrigeration circuit

Reversing Valve - All copper with low-pressure drop for maximum efficiency

Water Heat Exchanger - Extra capacity brazed plate or copper coil resists corrosion and allows maximum heat transfer

Hot Water Generator (Optional) - A double-wall desuperheater coil saves up to 65% on annual domestic water heating costs

Air Pad (Optional) - For even quieter operation

Refrigerant - Utilizes R22 refrigerant

Compressor - A hermetically sealed, pistonless Compliant Scroll™ by Copeland® delivers the highest efficiency and lowest sound level in the industry

Cabinet - Vertical or horizontal configuration with fully insulated baked-on powder epoxy

 

back to top

ECONAR GeoSource Vara 2 Plus® Forced Air 3-, 4-, 5-, and 7-Ton Heat Pumps

Three heating stages and two cooling stages provide the right amount of heating or cooling when needed at high efficiency

R-410A refrigerant - The next generation of refrigerant with no ozone depletion potential and increased energy savings

ECM Fan Motor – State-of-the-art, energy-efficient, variable-speed Electronically Commutated blower Motor provides significant cost savings compared to partial-load running of traditional PSC fan motors. All the comforts of a cleaner home and relief from airborne irritants without high fan-operating costs

Air Heat Exchanger and Filter - High-density technology coil with copper tubing in aluminum fins designed for cold climates to provide the highest heating output in the industry at comparable cooling capacities. Includes an Allergy Gold filter for a cleaner system and homeowner comfort. Convenient front-loading filter rack with door

Electrical Controls – Total compressor lockout is activated by electronic monitoring of low or high pressure for maximum system protection. Compressor and fan motors are staged for a softer start

Filter/Drier - Assures a clean, dry refrigeration circuit

Reversing Valve - All copper with low-pressure drop for maximum efficiency

Water Heat Exchanger – Brazed-plate stainless-steel heat exchangers provide maximum heat exchange at minimum pump pressure for reduced pumping costs

Hot Water Generator (Optional) - A double-wall desuperheater coil saves up to 75% on annual domestic water heating costs

Air Pad (Standard) Included for quieter operation

Thermostat (Standard) – Includes three-stage heat and two-stage cool electronic thermostat

Electric Heater (Standard) - Includes electric heater for emergency heat or third-stage assist

Refrigerant - R410a refrigerant, a chlorine-free HFC refrigerant that does not harm the Earth’s ozone layer

Blower – Variable-speed Electronically Commutated Motor (ECM) provides quiet, efficient air circulation

Thermostatic Expansion Valve - State-of-the art thermostatic expansion valve provides precise refrigeration control under a wide range of conditions

Charge Optimizer - Balances refrigerant charge in heating and cooling modes allowing optimum capacities and efficiencies

Compressor - A hermetically sealed, Compliant Scroll™ by Copeland® delivers the highest efficiency and lowest sound level in the industry

Cabinet - Vertical or horizontal configuration with fully insulated baked-on powder epoxy finish over galvaneal metal resists corrosion

 

back to top